Kürzlich haben wir festgestellt, dass Kriminelle vorgaben, AiPCBA zu sein, um zu betrügen oder zu versuchen, Fälschungen zu verkaufen
ausgefallene Komponenten zu günstigen Preisen.
AiPCBA hat ein
Komponentenprüflabor
im Jahr 2021 mit dem Ziel, qualitätsgesicherte Komponenten bereitzustellen.
Wir empfehlen unseren Kunden dringend, sich für zuverlässige Komponentenlieferanten zu entscheiden.
Bitte beachten Sie, dass die einzigen offiziellen Website- und E-Mail-Suffixe sind
aipcba.com
The SN65HVD233, SN65HVD234, and SN65HVD235 are used in applications employing the controller area network (CAN) serial communication physical layer in accordance with the ISO 11898 standard. As a CAN transceiver, each provides transmit and receive capability between the differential CAN bus and a CAN controller, with signaling rates up to 1 Mbps.
Designed for operation in especially harsh environments, the devices feature cross-wire protection, overvoltage protection up to ±36 V, loss of ground protection, overtemperature (thermal shutdown) protection, and common-mode transient protection of ±100 V. These devices operate over a wide 7 V to 12 V common-mode range. These transceivers are the interface between the host CAN controller on the microprocessor and the differential CAN bus used in industrial, building automation, transportation, and automotive applications.
**Modes:** The RS pin (pin 8) of the SN65HVD233, SN65HVD234, and SN65HVD235 provides three modes of operation: high-speed, slope control, and low-power standby mode. The high-speed mode of operation is selected by connecting pin 8 directly to ground, allowing the driver output transistors to switch on and off as fast as possible with no limitation on the rise and fall slope. The rise and fall slope can be adjusted by connecting a resistor between the RS pin and ground. The slope will be proportional to the pins output current. With a resistor value of 10 kΩ the device driver will have a slew rate of ∼15 V/µs and with a value of 100 kΩ the device will have ∼2.0 V/µs slew rate. For more information about slope control, refer to _Feature Description_.
The SN65HVD233, SN65HVD234, and SN65HVD235 enter a low-current standby (listen only) mode during which the driver is switched off and the receiver remains active if a high logic level is applied to the RS pin. If the local protocol controller needs to transmit a message to the bus it will have to return the device to either high-speed mode or slope control mode via the RS pin.
**Loopback (SN65HVD233):** A logic high on the loopback (LBK) pin (pin 5) of the SN65HVD233 places the bus output and bus input in a high-impedance state. Internally, the D to R path of the device remains active and available for driver to receiver loopback that can be used for self-diagnostic node functions without disturbing the bus. For more information on the loopback mode, refer to _Feature Description_.
**Ultra Low-Current Sleep (SN65HVD234):** The SN65HVD234 enters an ultra low-current sleep mode in which both the driver and receiver circuits are deactivated if a low logic level is applied to EN pin (pin 5). The device remains in this sleep mode until the circuit is reactivated by applying a high logic level to pin 5.
**Autobaud Loopback (SN65HVD235):** The AB pin (pin 5) of the SN65HVD235 implements a bus listen-only loopback feature which allows the local node controller to synchronize its baud rate with that of the CAN bus. In autobaud mode, the bus output of the driver is placed in a high-impedance state while the bus input of the receiver remains active. There is an internal D pin to R pin loopback to assist the controller in baud rate detection, or the autobaud function. For more information on the autobaud mode, refer to Feature Description.
 Die hier aufgeführten Geschäftsbedingungen dienen nur als Referenz, die tatsächlichen AGB unterliegen dem Angebot des Verkäufers. - Bitte bestätigen Sie die Spezifikationen der Produkte bei der Bestellung. - MOQ bedeutet die Mindestbestellmenge, die erforderlich ist, um jedes Teil zu kaufen. - Wenn Sie spezielle Bestellanweisungen haben, vermerken Sie diese bitte auf der Bestellseite. - Die Pre-Shipment Inspection (PSI) wird angewendet. - Sie können uns jederzeit eine E-Mail senden, um den Bestellstatus zu überprüfen. - Bestellungen können nach Versand der Pakete nicht mehr storniert werden.
- TT im Voraus (Banküberweisung), PayPal kann ausgewählt werden. - Nur Barüberweisung. (Überweisungen mit Schecks und Wechseln werden nicht akzeptiert.) - Der Kunde ist für die Zahlung aller möglichen Gebühren verantwortlich, einschließlich Umsatzsteuer, Mehrwertsteuer und Zollgebühren usw. - Wenn Sie die detaillierte Rechnung oder Steuernummer benötigen, senden Sie uns bitte eine E-Mail.
- FedEx, DHL und UPS können ausgewählt werden. - Sie können auswählen, ob die Versandkosten von Ihrem Versandkonto oder von unserer Seite berechnet werden sollen. - Bitte bestätigen Sie dies im Voraus mit dem Logistikunternehmen, wenn Sie sich in einem abgelegenen Gebiet befinden.
(Es können zusätzliche Gebühren (35-50 USD) für die Lieferung in diese Gebiete anfallen.) - Lieferdatum: normalerweise 2 bis 7 Werktage. - Tracking-Nummer wird gesendet, sobald Ihre Bestellung versandt wurde.
- Sorgfältig geprüft und verpackt von AiPCBA - Vakuumverpackung - Antistatische Verpackung - Antivibrationsschaum
- Einkommensqualitätskontrolle (IQC), über 800 qualifizierte Vertriebspartner. - 500 m² Labor für fortschrittliche Komponententests, Fälschungserkennung, RoHS-konform usw. - 2000 m² digitales Komponentenlager, konstante Temperatur und Luftfeuchtigkeit - Entkapselungsinspektion - Röntgeninspektion - XRF-Inspektion - Elektrische Prüfung - Oberflächenprüfung
- Substandard- und Fälschungserkennung - Fehleranalyse - Elektrische Prüfung - Lebenszyklus- und Zuverlässigkeitstests - AiPCBA hat 2021 ein Komponententestlabor eingerichtet
Mehr erfahren >
AiPCBA verwendet Cookies, um Ihnen ein besseres Erlebnis zu bieten. Detaillierte Informationen zur Verwendung von Cookies auf dieser Website finden Sie in unserer Datenschutzerklärung. Durch die Nutzung dieser Website stimmen Sie der Verwendung von Cookies zu.